How To Install Neutral Lug Kit
How to Install Lug Basics
Sure, lug basics are relatively small parts. Just at that place's quite a chip of knowledge and technique that goes into fitment and installation. Lug basics are disquisitional components responsible for holding the wheels on your vehicle. These small parts experience farthermost forces and it's essential that fitment and installation is handled properly.
Nosotros hope that you find this handy installation guide helpful for your next installation project.
Before You lot Start
Installation by a professional technician is highly recommended. Please read this entire guide before installation and make sure the fitment is correct for your application.
- Always apply new lug nuts when installing new wheels.
- Never use lubricants on lugs or studs. This may event in loss of torque or failure of bike studs.
- Practise non apply air affect wrenches to tighten your lugs. This may result in weakening of your wheel studs causing them to fail while driving.
01 Lug Nut Fitment Checklist
The kickoff and virtually important stride to lug nut installation is making sure you have the correct fitment for your vehicle and cycle awarding. Failure to use the correct lug nuts will cause dangerous driving atmospheric condition that tin result in wheel loss while driving. Only use lug nuts designed to fit your vehicle and wheel application.
Use the checklist beneath to verify your lug nut fitment prior to installation or contact a Driven Products Fitment Specialist for assistance.
- Thread Size and Thread Pitch - Each lug nut has a specific thread size and thread pitch adamant by your vehicle specifications. For example, the wheel studs on a 2018 Ford F-150 will require lug nuts with a M14x1.v thread size. The thread size of the lug nut must match your vehicle'due south wheel studs.
- Seating Style - In that location are three mutual types of lug nut seating styles adamant past your type of wheels: (1) cone or tapered seat, (two) mag or shank seat, and (3) radius or ball seat. The seating style of the lug nut must lucifer the wheel lug seat. Using the wrong seating style will cause vibration, loosening of lug basics, or damage to your vehicle.
- Lug Mode - Different types of wheels crave different styles of lug nuts. For example, most aftermarket wheels will require a small diameter lug while most manufactory manner wheels volition require a larger diameter lug. About pocket-sized diameter lugs will be dangerous to install on factory wheels.
- Minimum Thread Date - The thickness of a wheel tin can differ from factory wheels to aftermarket wheels. For that reason, it's essential to verify that the lug nuts will properly engage the threads on your vehicle'due south wheel studs. Refer to our minimum thread appointment chart to make up one's mind the number of turns, or depth of date, typical for your stud or bolt size.
02 Gear up For Installation
Now that you lot've verified lug nut fitment, it'due south fourth dimension to gear up your vehicle for installation and remove your current lugs.
- Park on a hard, level surface and apply parking restriction.
- Loosen the lug nuts 1 quarter plough but exercise not remove them from the wheel.
- Raise up your vehicle post-obit the procedure outlined in your vehicle owner's manual.
- Secure the wheel and remove the lug basics, then the wheel.
03 Install Your Lug Basics
Nosotros recommend using the RIST method of lug nut installation which the Tire Industry Association refers to in its Automotive Tire Service training plan. The RIST method involves: (R) Removing debris from mounting surfaces, (I) Inspecting components for damage or excessive wear, (S) Snugging the lugs in a star blueprint, and (T) Torquing to manufacturer specifications. Follow all instructions in the order presented.
- Make clean and inspect all stud threads and mounting surfaces before installation. Threads must not exist lubricated and must exist free of corrosion, rust, burrs, fractures, and damage. Replace studs if they are corroded, stripped, damaged, or if whatever fractures are found.
- Place the wheel back onto the vehicle hub. Match the commodities circumvolve of the wheel to that of your vehicle. The wheel must brand total contact with the mating surface of the hub.
- Install your lug nuts and tighten with your manus in a star, or criss cross, design until y'all cannot paw tighten anymore. Refer to our bike torque sequence chart to determine proper pattern and sequence for your installation. Practice not strength your lugs on with a wrench. If they cannot be turned by hand, end installation and contact a Driven Products Fitment Specialist.
- One time all lug nuts have been tightened to meet minimum thread date and your cycle is sitting flush against the mating surface, lower the vehicle to ground and tighten all lug nuts to the proper torque specifications shown in your vehicle owner'south manual. We recommend using a calibrated torque wrench for this pace. Utilize torque evenly by repeating the star, or criss cross, pattern until the desired torque is reached.
- Always re-torque your lug nuts after the first 25 miles of employ each fourth dimension the lug nuts are removed and installed. Failure to re-torque could effect in dangerous driving weather.
04 Post Installation Checklist
You're virtually there! We recommend that the post-obit safety checklist be completed after installation. This checklist is not intended to replace the installation guide above. Instead, we've included this checklist to help ensure major condom points were checked earlier, during, and afterwards the installation process. If any item was not performed on the checklist, delight consult your installer or contact a Driven Products Fitment Specialist.
- Lug nuts are verified to be the right fitment for your vehicle and wheel application, including thread size, seating style, lug style, and minimum thread engagement.
- All threads and studs are free from rust, corrosion, fractures, lubricant, etc.
- Air impact wrenches were not used to install the lug nuts.
- All lug nuts are tightened to the proper torque specification with a calibrated torque wrench.
- All lug nuts have been re-torqued after the first 25 miles or driving.
Frequently Asked Questions (FAQs)
Can you drive a automobile with a missing lug nut?
If y'all're missing a lug nut, you should have it replaced equally soon as possible. A missing lug nut could pb to dangerous driving conditions because of the extra force exerted on the wheel. This pressure can damage the wheel bearings, studs, and cause other lug nuts to fail leading to failure of the bicycle while driving.
Can loose lug nuts cause damage?
When a lug nut is loose, the clamping forces are redistributed amid the remaining lugs and studs. The loosening process will advance with each lug that loosens, causing the total clamping force to drop and the forcefulness on the remaining lugs and studs to increase. The studs can then fracture which will accelerate the procedure if non detected and corrected quickly.
How tight should you tighten your lug nuts?
Lug nuts should always exist installed using a calibrated torque wrench to the torque specifications shown in your vehicle owner's manual. Both undertorquing and overtorquing are mutual when air touch on wrenches are used.
Why do wheels come loose?
Loose wheels are typically the result of an improper or careless installation. Threads must non be lubricated and must be complimentary of corrosion, rust, burrs, fractures, and damage. Failure to follow the torque specifications in your vehicle owner's manual, correct wheel torque sequence, or routine torque checks have all been cited every bit causes for loss of clamping strength on lug nuts.
Comments
darrell day - January 17, 2022I have worked for at least 6 different tire shops over the years. Most tighten lugs with air guns! A few actually followed directions. I think you might add an air gun tightening guide. People encounter all racers use air guns.
Source: https://www.drivenproducts.com/blogs/diy/how-to-install-lug-nuts
0 Response to "How To Install Neutral Lug Kit"
Post a Comment